Interskol FM-67/2200E (121.1.0.00)
Diamond Core Bits & Milling Cutters3039
 |
Tungsten Carbide Tipped. Two flute cutter with tips sheared up and down, giving a fine finish. For trimming veneered and double-faced boards, plywoods and natural timbers. These cutters have the more→action of pushing the chips towards the middle of the board being cut, thus ensuring that the veneers are sheared off cleanly in the process. Specifications • Shank Diameter: 1/2 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 54 • Overall Length Metric: 108
 |
Trend Craft Pro 1/4in shank straight router cutter - 12.7mm diameter Two Flute Carbide tips Two flute carbide TCT tips for cleaner cutting edges and fast clearance of waste in all timber and timber b more→ased materials. With bottom cut feature for general purpose slotting, grooving and 31.8mm deep cutting depth for deeper morticing work on light joinery and furniture work. 12.7mm diameter X 31.8mm cutting depth ideal for matched slots and grooves with sheet material for panel work, deep rebating and trimming. PTFE coating to minimise heat and resin build up for increased cutter performance and longevity. 1/4in shank for easy control in smaller routers with 'K'mark shank to ensure safe working …
 |
Two flute TC cutter giving good chip clearance. Ideal for shallow lateral routing cuts such as recessing hinges. Corners will require final trimming square with a hand chisel or a corner chisel. more→Suitable for Trend Hinge & Lock Jigs. Specifications • Shank Diameter: 1/4 • Dia Metric: 12 • Dia Imperial: 15/32 • Cut Length Metric: 19 • Overall Length Metric: 70
 |
Tungsten Carbide Tipped. Two flute cutter with a positive shear angle (down-cut) for fast cutting and fine finish. Ideal for grooving & trimming veneer finishes & laminated boards. Down cut feature more→stops break out on top edge. Has a 4 degree shear. Specifications • Shank Diameter: 1/2 • Dia Metric: 9.5 • Dia Imperial: 3/8 • Cut Length Metric: 25 • Overall Length Metric: 70
 |
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Sp more→ecifications • Shank Diameter: 1/2 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Metric: 25 • Cut Length Imperial: 1 • Overall Length Metric: 64
 |
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications • Shank Diam more→eter: 1/4 • Dia Metric: 19.1 • Dia Imperial: 3/4 • Cut Length Metric: 25 • Overall Length Metric: 58
 |
Ideal for following template. It is advisable that the template is at least 5mm thicker than the cut length of the tool. Specifications • Shank Diameter: 1/4 • Dia Metric: 22 • Cut Len more→gth Metric: 10 • Cut Length Imperial: 25/64 • Overall Length Metric: 61.5 • Bearing Dia Metric: 22 • Radius 1 Metric: 2.4
 |
This set incorporates two drill countersinks and matching plug cutters. Plugs cutters are made from Tool Steel and are very slightly tapered. Use on timber to drill a countersunk hole for a screw wh more→ich is then plugged uses a plug/pellet made using the plug cutter. Recommended that plug cutters are used in a pillar drill. Specifications • Shank Diameter: 1/4 hex • Type or Grade: For No.8 & 10 • Pack Qty: 4 piece Contents: 1 x Drill/countersi
Important!
Compatibility with specific models Routers & Trimmers should be confirmed with the online store manager directly before purchase.
Compatibility with specific models Routers & Trimmers should be confirmed with the online store manager directly before purchase.