Comparison FiiO KA13 vs FiiO KA3

DAC model — a digital-to-analogue converter installed in the amplifier.

In accordance with the name, the DAC is responsible for converting a digital signal (for example, coming to the optical input or USB, see "Inputs") into an analogue format, with which the amplifier directly works. The presence of such a converter in an external "amplifier" is important, given the fact that many popular signal sources — such as smartphones or built-in sound cards — are equipped with fairly simple and inexpensive DACs with low sound quality; on external equipment, this quality can be much higher. And the quality of the conversion and, accordingly, the characteristics of the output sound directly depend on the characteristics of the DAC: even the most advanced power amplifier will not “save” a signal converted with significant errors. Accordingly, knowing the converter model, you can find detailed data on it — from official specifications to practical reviews — and evaluate how an amplifier with such a module meets your requirements.

The sampling rate of the digital-to-analogue converter (DAC) installed in the amplifier. Recall that such a converter is responsible for converting digital audio into an analogue audio signal, which is then processed by the main amplifier and fed to the headphones (or other analogue audio device).

The sound in digital form is most often recorded as follows: the original sinusoid of the analogue audio signal is divided into separate sections (samples) — “steps” of a certain length and height, and each of these steps is encoded with its own set of numbers. The sampling rate determines how many such steps there are in a certain section of the original audio signal. Accordingly, the higher this frequency, the more accurately the digital record corresponds to the original signal; on the other hand, an increase in the number of samples per unit of time increases the volume of files and increases the requirements for the hardware power of digital circuits.

Specifically, for a DAC, the native sampling rate of such a module is, in fact, the maximum sampling rate of the incoming digital signal that the converter can effectively handle. With higher input values, the sound quality will at best be limited by the capabilities of the DAC, at worst, the amplifier will not be able to work correctly at all. Anyway, higher numbers in this paragraph (ceteris paribus) mean a more advanced and high-quality converter; on the other hand, this moment significantly affects the...cost, and you can evaluate all the capabilities of a high-end DAC only on audio materials of the appropriate quality.

As for specific numbers, the lowest value that can be found in headphone amplifiers is 44 kHz. According to the laws of physics, it is this sampling frequency that is the minimum necessary for the full transmission of all human-audible sound frequencies (16 — 22,000 Hz), and it is this frequency that is used in the Audio CD format. Many models provide values in 96 kHz and 192 kHz (this is already enough to work with different types of DVD-Audio), and in the most advanced devices this figure can reach 384 kHz and even 768 kHz.

Rated headphone output(s) provided by the amplifier.

Rated is the highest average power that the device is capable of delivering for a long time without overloads; individual “jumps” of the signal may have a higher level, but this indicator is the main one. The sound volume of the headphones connected to the device directly depends on it: with the same characteristics of the “ears” (primarily sensitivity), the high output power of the amplifier allows for a higher sound pressure level.

There are special formulas and tables that allow you to calculate the minimum power level required to achieve a particular volume. For example, to achieve 95 dB (the minimum required level for listening to music in silence at a satisfactory volume), headphones with a sensitivity of 100 dB will need 0.32 mW, for 105 dB (recommended level for powerful sound like rock concerts) — 3, 16 mW, and for 120 dB (the recommended level for watching movies with special effects like thunder, explosions, etc.) — already 100 mW.

At the same time, when choosing by this parameter, note that the actual power of the amplifier at the output will depend on the impedance of the headphones. This paragraph usually indicates the highest power value — with the minimum allowable resistance; for "ears" with numerous ohms, the power will be less, sometimes quite significantly. Therefore, when choosing, it is more convenient to use not a total number, but a specific power value for a parti...cular resistance (see below). The second nuance is that for multichannel amplifiers (see "Number of channels") this parameter can be indicated in different ways: in some models, the power is given for the full channel load mode (that is, we are talking about a guaranteed maximum per channel), in others — for half load or generally for working with one channel; such details should be clarified separately.

Rated power delivered by the amplifier when connected to headphones (or other load) with an impedance of 32 ohms.

By itself, the rated power is the highest average power that the device is capable of delivering for a long time without overloading; individual "jumps" of the signal may have a higher level, but in general, the capabilities of the amplifier are determined primarily by this indicator. At the same time, the physical features of the audio equipment are such that the actual power delivered to the load will depend on the resistance of this load. Therefore, in the characteristics of headphone amplifiers, data is often given for different impedance values. A resistance of 32 ohms allows you to achieve quite good sound quality by the standards of low-impedance headphones, while it is not so high as to create problems for the built-in amplifiers of smartphones and other compact equipment. Therefore, most wired general-purpose (non-professional) headphones are made precisely in this resistance, and if the amplifier characteristics generally indicate power for a certain impedance, then most often it is for 32 ohms.

In the most modest modern amplifiers, the output power at this impedance is between 10 and 250 mW ; values of 250 – 500 mW can be called average, 500 – 100 mW are above average, and the most powerful models are capable of delivering ...f="/list/788/pr-19429 /">more than 1000 watts. The choice for specific power indicators depends on the sensitivity of the headphones used, as well as on the sound pressure level (in other words, loudness), which is planned to be achieved by the amplifier. There are special formulas and tables that allow you to calculate the minimum required power for a certain volume at a given sensitivity of the "ears". However, in the case of 32-ohm headphones, it does not always make sense to "get into the calculations." For example, the mentioned 10 mW is more than enough to drive headphones with a modest sensitivity of 96 dB to a volume of more than 105 dB — this is already enough to listen to music at quite a decent volume. And in order to achieve the same "ears" level of 120 dB, which provides a full perception of the loudest sounds (like explosions, thunder, etc.), you need to give out a power slightly higher than 251 mW. So in fact, you have to pay attention to this characteristic and resort to calculations / tables mainly in those cases when you have to use 32 Ohm headphones with a relatively low sensitivity — 95 dB or less.

Frequency range supported by the output amplifier; in other words, the range that this model is capable of delivering to headphones or another analogue audio device.

Theoretically, the wider the frequency range — the richer the sound of the amplifier, the lower the likelihood that the lower or upper edge of audible frequencies will be “cut off”. However, when evaluating this parameter, several nuances should be taken into account. Firstly, the average person is able to hear frequencies from 16 to 22,000 Hz, and with age, these boundaries gradually narrow. However, headphone amplifiers often have wider operating ranges, and they are very impressive — for example, for some models, a set of frequencies from 1 Hz to 60,000 Hz, or even up to 100,000 Hz, is claimed. Such characteristics are a kind of "side effect" from the use of high-end sound processing circuits; from a practical point of view, these numbers do not make much sense, but they are an indicator of the high class of the amplifier and are often used for advertising purposes.

The second nuance is that any headphones also inevitably have their own frequency limitations — and these limitations can be more significant than in an amplifier. Therefore, when choosing, it's ok to take into account the characteristics of the headphones: for example, you should not specifically look for an amplifier with an upper frequency limit of the full 22 kHz, if in the headphones that you plan to use with it, th...is limit is only 20 kHz.

In conclusion, also note that an extensive frequency range in itself does not guarantee high sound quality — it largely depends on other factors (frequency response, distortion level, etc.).

The coefficient of harmonic distortion that occurs during the operation of the amplifier.

Any electronic circuits are inevitably subject to such distortions, and the quality and reliability of the sound at the output depends on their level. Accordingly, ideally, the harmonic coefficient should be as low as possible. So, as a general rule, a level of 0.09% and below (hundredths of a percent) is considered good, and a level of less than 0.01% (thousandths of a percent) is excellent. The exception is lamp devices: higher values \u200b\u200bare allowed in them (in tenths of a percent), however, this point in many cases is not a drawback, but a feature (for more details, see "Lamp").

It is also worth noting that a low harmonic coefficient is especially important when using the amplifier as part of multicomponent audio systems — for example, when listening to music from a vinyl player with an external phono stage. The fact is that in such systems the sum of distortions from all components affects the final sound — and it, again, should be as low as possible.

The way to adjust the level provided in the amplifier, in other words, the way to control the volume.

Most often, a special wheel(rotary control) is responsible for such adjustment, however, there are also models with buttons. Here are the features of each option:

— Wheel. The most common type of volume control nowadays; its popularity is due primarily to two things. The first is ease of use: the control of the wheel is intuitive, and besides, such a knob can be found and turned by touch, blindly, without much difficulty (this is especially important for portable models — see "Type"). The second point is versatility: the wheel can be connected both with the simplest analogue control loop and with a digital circuit. Moreover, analogue control (considered optimal for high-end equipment) in modern headphone amplifiers is carried out only by rotary controls. The disadvantages of this option include perhaps some bulkiness compared to buttons, but even in pocket models this moment is often not critical.

— Buttons. Volume control with buttons; it can be either two separate keys or a rocker like those used in many portable gadgets. Anyway, such controls are more compact than castors. On the other hand, such control is carried out only electronically: the buttons send a signal to the control circuits, which change the volume accordingly. This format is considered less suitable for h...igh-quality audio equipment than analogue control: additional digital circuits not only complicate the design, but are also a potential source of additional noise. Therefore, push-button control can rarely be found nowadays — in certain models of portable amplifiers (see "Type"), where this solution is provided mainly to reduce the size.