Comparison MikroTik RB5009UG+S+IN vs Teltonika RUTX09

— Desktop. Desktop routers include routers that do not use special rack mounts and are suitable for placement on any suitable surface — a table, shelf, etc. Although there are quite advanced models among desktop devices, however, most of them have relatively simple functionality and are designed for use in small networks where an abundance of equipment is not required.

— Rack mounted. Routers that are standard installed in a telecommunications rack are usually 19 "standard (although technically many of them can also be used as desktop ones, albeit with less convenience). Racks are used in extensive networks that require a large amount of equipment; accordingly, routers of this type in general, more powerful and advanced than the desktop, and are designed primarily for professional use.

— To the mast. Installation on a mast or other vertical structure — a tower, a pole, etc. Quite a rare form factor; It is mainly used in waterproof models designed for the possibility of working outdoors. Mobile network capable devices in this category may have a directional antenna to improve connectivity.

How the router connects to the Internet or other external network.

Almost all modern routers have ethernet network connectors for this purpose, however, in addition to them, other connection options can be provided — both wired ( ADSL, SFP / SFP + optics) and wireless (mobile access via 3G / 4G modem or SIM card). Here are the features of each option:

— Ethernet. A standard LAN network cable connector (“twisted pair”) is the most popular modern wired connection format in computer networks. Widely used both in "local" and to provide access to the Internet. This standard is somewhat inferior to SFP / SFP + (see below) in terms of speed and noise immunity, but it is much cheaper. The speed of work in modern versions of Ethernet can reach 10 Gbps (see "Connection speed of WAN ports"), theoretically, a further increase in throughput is possible.

— SFP / SFP + (optics). A connector for transmitting network traffic over a fiber optic cable. The main advantage of such a cable is complete insensitivity to electromagnetic interference. And data transfer rates can reach 2.7 Gbps in the original SFP and 16 Gbps in SFP+. At the same time, maintaining this standard is not cheap, and the benefits mentioned are not often needed in fact. Therefore, SFP / SFP + is found mainly in mid-range a...nd top-level routers.

— ADSL. Connecting to the Internet through a fixed telephone network using ADSL technology. The key advantage of this connection is the ability to use existing networks without laying additional wires; at the same time, Internet access is completely separated from telephone communication and traffic does not interfere with voice calls. On the other hand, the bandwidth of ADSL is very low by modern standards (less than 24 Mbps), moreover, the data transmission speed is noticeably lower than the reception speed. This can create problems for video communication and some other specific tasks. So nowadays ADSL is used less and less.

— 3G/4G modem (USB). Internet connection via mobile network using a separate 3G or 4G modem connected to the USB port. This feature can be useful where there is no full-fledged wired connection (for example, in rural areas), and also as a fallback option in case the main communication channel fails. And the type of network supported depends mainly on the modem used (the compatibility of the router with different models needs to be specified separately, but most often there are no problems with this). As for specific types of networks, most 3G modems work in UMTS networks (the same ones that are massively used by mobile phones); the data transfer rate in such networks can reach 75 Mbit / s (however, usually it is much lower). Less common are 3G modems for EV-DO networks based on CDMA — this standard has lower speeds (up to 14.7 Mbps) and not as extensive coverage as UMTS, however, both the equipment and the connection itself can be cheaper. And the designation "4G" means only one type of networks — LTE; it provides speeds up to 173 Mbps, but is not as widespread as 3G.

— SIM card. Another option for connecting to the Internet via mobile networks is its own SIM card slot provided in the design of the router. This option is convenient because you do not need to buy an additional device (modem) for mobile Internet — you just need to purchase an operator's SIM card. On the other hand, due to the built-in mobile communication modules, such routers themselves are more expensive than analogues for USB modems. In addition, the connectivity options in them are limited by the characteristics of the module: for example, a router for 3G networks will not be able to fully use 4G networks (whereas a USB modem can usually be changed to a more advanced one). As a result, this option is relatively rare in modern equipment.

4G (LTE) mobile speed supported by the device.

All modern LTE equipment is assigned one category or another, which directly affects the data transfer speed. This paragraph clarifies both this category and specific speed indicators, both in two parameters - for reception and transmission. The transmission speed is always significantly lower, but given the specifics of mobile Internet access, this moment is usually not critical.

Note that equipment with different speed categories will be quite compatible with each other, however, the throughput will be limited by the capabilities of the slower device. It is also worth saying that this paragraph indicates a theoretical maximum; practical indicators can be noticeably lower (depending on the quality of the coverage, air load, and the features of specific electronics). However, a router with a higher speed category will in practice be faster.

The number of standard Gigabit Ethernet RJ-45 network connectors provided in the device design.

As the name suggests, these connectors provide data transfer rates up to 1 Gbps. Initially, Gigabit Ethernet was considered a professional standard, and even now the real needs for such speeds arise mainly when performing special tasks. Nevertheless, even relatively inexpensive computers are now equipped with gigabit network adapters, not to mention more advanced technology.

As for the number of connectors, it corresponds to the number of network devices that can be connected to the "switch" directly, without the use of additional equipment. At the same time, it is worth noting that in some "switches" individual connectors of this type are combined with optical SFP or SFP +. Such connectors are marked "combo" and are taken into account both when counting RJ-45 and when counting SFP / SFP +.

The number of standard network connectors RJ-45 format 2.5 Gigabit Ethernet, provided in the design of the device. These ports are backwards compatible with lower speeds. This type of ports can be used in conjunction with NAS servers or, for example, with routers that support Wi-Fi 6/6E, where this format has also become widespread.

The number of SFP+ optical ports provided in the device design.

The general advantages of fiber optics over regular Ethernet cables are longer communication ranges and insensitivity to electromagnetic interference. Specifically, SFP+ is a development of the original SFP standard; Such connectors operate at a speed of 10 Gbit/s as standard. As for the number of such ports, despite all its advantages, optical fiber in network equipment is still used quite rarely and most often there is only 1 port(less often 2 ports or more). It is also worth considering that there may be so-called combo connectors that combine SFP+ and RJ-45; the presence of such ports is specified in the notes; they are taken into account both when calculating RJ-45 and when calculating SFP+.

The number of ports designated as WAN by the manufacturer. They are intended for wired connection of the device to the Internet or other external networks (to solve some specific problems).

In this case, dedicated LANs mean directly marked network connectors designed for wired connection of LAN devices - PCs, servers, additional access points, etc. The number of ports corresponds to the number of devices that can be directly connected to the equipment by wire.

The model of the processor installed in the device. The processor is responsible for processing network traffic and running software. Knowing its name, you can get more detailed data on the speed capabilities of the equipment and understand how much such a powerful or, on the contrary, mediocre element is needed on board. In new models of Wi-Fi equipment, coprocessors or so-called NPU modules are often installed, which relieve the load from the main processor.