Comparison Technics SL-1200MK7 vs Technics SL-1210MK7

The force of pressing the needle on the plate, which the complete pickup (cartridge) is designed for.

This force depends on the rigidity (compliance) of the needle: the greater the clamping force, the harder the cartridge, respectively, the less pliable it is. It is also believed that less pressing force wears out the record less, but it cannot be said that "light" cartridges are definitely better — there are many other nuances. So in fact, information about the pressing force of a complete pickup is needed mainly in case of its replacement. Usually, the pressing force provided by the arm of the turntable is regulated within these limits, so the new cartridge must also be rated for the same values of downforce — otherwise there is a chance that the turntable will not be able to correctly align.

The weight of the pickup (cartridge) supplied with the turntable.

The weight of the cartridge determines the characteristics of balancing the tonearm to set the optimal tracking force. However, pickups in set are usually optimally compatible with the corresponding tonearms, so there are no problems with adjusting the turntable. But when buying a replacement cartridge, you should pay attention to this parameter: it is advisable that the new cartridge does not differ too much in weight from the old one, otherwise the tonearm adjustment range may not be enough for the correct balance.

The shape of the complete tonearm (viewed from on top). Modern players may have both straight and S-shaped or J-shaped tonearms. It is impossible to say for sure which of them is better: the advantage of the first option is its light weight, the second and third ones are its greater length and low resonant frequency, which reduces the likelihood of interference. Therefore, in practice, the choice depends on the specific situation and personal preferences.

The main material used in the construction of a complete tonearm.

- Aluminum. This is a fairly lightweight and durable material that has average characteristics in terms of sound quality: it does not dampen extraneous vibrations as well as carbon, but for entry-level and mid-level turntables this is quite enough; in expensive models, you can use other methods of eliminating interference, and aluminum is noticeably cheaper.

— Carbon. A high-quality material that is lighter in weight and has more advanced anti-resonance properties than the metal described above. The main disadvantage of carbon fiber is its rather high cost.

- Plastic. Plastic is inexpensive, but this is perhaps its only key advantage: the performance characteristics of this material are quite modest. That is why it is used extremely rarely - mainly in retro-style players, where a plastic tonearm is a necessary part from a design point of view.

A method for switching the disc rotation speed provided in the player.

— Manual. This option is only found on belt driven models (see above). It provides the transfer of the belt to another pulley, due to which the gear ratio and, accordingly, the rotation speed change. This method is not as fast and convenient as automatic, however, it allows you to do without unnecessary electronic circuits (many audiophiles appreciate this feature, because additional electronics can interfere and degrade sound quality).

— Electronic. Speed switching, carried out by changing the parameters of the electric motor — usually, the user just needs to press a button or move the regulator. This method is much faster and more convenient than mechanical, and for direct drive models (see above) is generally the only possible option. However, the electronics responsible for switching the speed affect the cost of the player and can become a source of additional interference; however, the latter can be compensated by installing control circuits in an external power supply (see below).

The presence in the design of the player or a dust cover, or devices for its installation (the cover itself is not included in the kit).

Both vinyl records and the equipment for playing them require protection from dust: settling on the tracks, dust leads to extraneous noise and increased wear of the records and needle. Thus, for normal listening to music, it is highly recommended to have a turntable with a lid — otherwise you will have to regularly clean up. But for a DJ "turntable", the lid, on the contrary, is an excess.

A phono corrector is a specially designed preamplifier used when working with vinyl record pickups. Initially, the sound on such records is recorded with distortion of the amplitude-frequency characteristic, namely with an increase in volume from low to high frequencies; this is due to the technical features of the recording process. Accordingly, the phono corrector not only amplifies the signal to a level sufficient for feeding to the power amplifier, but also corrects the amplitude-frequency characteristic, “pulling out” the bass and reducing the volume of the HF. And the built-in phono corrector allows you to connect the player to the power amplifier directly, without using intermediate equipment. True, in terms of characteristics, built-in preamplifiers-correctors are inferior to external ones. Therefore, some models with this function may provide a “bypass” mode, allowing you to pass the signal bypassing the built-in phono corrector to an external, more advanced one. And there are also vinyl players without a phono corrector at all.

The presence in the player of an electronic module that allows you to change the tone of the sound being played, in other words, to make it higher or lower by a certain interval, in other words, change the playback speed. This feature is also known as a "pitch controller".. It is relevant primarily for DJ "turntables", as it allows you to mix tracks recorded in different keys. Some home players also have a tempo control, but its capabilities are much more modest, and a real need for such a function rarely arises.

The material used for the base of the turntable - or, as it is also called, the support table.

The base is actually the body of the turntable; the tonearm, platter and drive are mounted on top of it. Note that a set of modern turntables can include both a base and a base with a tonearm, and the most extensive option, called a complete set, also includes a pickup. As for the materials for the base, they must meet specific requirements - in particular, they must be quite heavy to reduce extraneous vibrations transmitted to the device. Here are the most common materials:

- Plastic. The main and, in the case of vinyl players, practically the only advantage of plastic is ease of production and, accordingly, low cost. At the same time, the performance characteristics of such material are quite modest, so it is the prerogative of inexpensive “turntables”.

— Acrylic. Technically, acrylic is a type of plastic described on top, but in general this material is much more advanced in performance characteristics, is relatively inexpensive and can have an original appearance (in particular, it can be made transparent). Acrylic tables are typical for fairly solid models.

- Aluminum. Metal bases made of aluminum are massive and highly durable, b...ut they are not cheap, and therefore are found mainly in premium players.

— MDF/Fibreboard. Fiberboards, in addition to good acoustic characteristics, are notable for their pleasant appearance, especially suitable for retro-style devices. This material can be used in quite expensive models.

- Carbon. High-quality material, characterized by high strength and quite stylish appearance. On the other hand, it has a relatively low weight, which has to be compensated by the significant thickness of such bases, and this affects the cost (despite the fact that the material itself is not cheap anyway). Therefore, carbon has not gained much popularity.

- Granite. Natural granite is very heavy and dampens vibrations well, but it is also a very expensive material. It is used extremely rarely, mainly in premium players, not only for the sake of practical characteristics, but also to emphasize the level of the device.